Lower-extremity support AM-TUD-KD

Lower limb immobilizer is made of ActiveDistance II™.

The brace was equipped with:

1. Open and soft sleeve which enables to adjust the device to the diverse measurements of bottom limb.
2. System of VELCRO stickers which assure proper adhesion the device to the body and more effective stabilization of limb.
3. System of anatomically profiled aluminium splints with independent fixing system to brace’s sleeve.

Such construction of article makes possible to adjust the device individually, easily and precisely to the patient’s body as well as assures sure stabilization of limb.

Purpose of use

Should be applied in cases of:

• knee dislocation,
• knee twist and sprain,
• side instability of the knee joint,
• knee ligaments LCL, MCL and ACL injuries,
• knee ligaments reconstruction,
• other surgeries (orthopedic)

Size	(A) Thigh circumference 15 cm (5,9″) above the center of the patella	(B) Calf circumference 15 cm (5,9″) below the center of the patella	(C) Product length	How to measure
S	min 40 cm – max 44 cm (min 15,7″ – 17,3″)	min 30 cm – max 34 cm (min 11,8″ – max 13,4″)	40 cm (15,7″)
M	min 44 cm – max 48 cm (min 17,3″ – max 18,9″)	min 34 cm – max 38 cm (min 13,4″ – max 15″)	50 cm (19,7″)
L	min 48 cm – max 52 cm (min 18,9″ – max 20,4″)	min 38 cm – max 42 cm (min 15″ – max 16,5″)	60 cm (23,6″)
XL	min 52 cm – max 56 cm (min 20,4″ – max 22″)	min 42 cm – max 46 cm (min 16,5 – max 18,1″)	70 cm (27,5″)
XXL	min 56 cm – max 60 cm (min 22″ – max 23,6″)	min 46 cm – max 50 cm (min 18,1″ – max 19,7″)

Total length of the product:
S: 40 cm (15,7″)
M: 50 cm (19,8″)
L: 60 cm (23,6″)
XL: 70 cm (27,6″)
2XL: 70 cm (27,6″)

Click on the photo to enlarge

MATERIALS

ActiveDistance II™

ActiveDistance II™ is an active 3-layered fabric made of non-elastic polyamide self-gripping layer, comfort foam and cotton terry. The last one layer is responsible for maintaining your skin dry. This material is skin-friendly and has the Oeko-Tex Standard 100 certificate. Self-gripping function of ActiveDistance II™ allows to fit the braces precisely.

STIFFENINGS

Flat aluminum stays

Aluminum stays are made of a special aluminum alloy that guarantees proper stiffness with minimal weight. They have rounded ends to prevent the damage of the product and come in various widths and thicknesses. The level of stabilization of the orthopedic device is defined by proper selection of the width and thickness of the aluminum stays. The stays can be pre-profiled or flat. They do not adapt to the shape of the patient's body, an individual adjustment of the orthosis is required by proper bending of the aluminum stays in the product. Thanks to this function, it is possible to correct the position of the patient's body or the secured joint.

Profiled aluminum stays, spine stabilizers

These are splints and orthopedic stays of various thickness and width, which are made of various types of aluminum alloys. All these splints and stays, before mounting to a given orthosis, have been pre-profiled, which allows for fitting the product to the body of a specific patient. However, for the correct operation of the device, they should be precisely bent to the patient's body by an orthopedist, physiotherapist or orthopedist technician. Only this action guarantees the proper protection and support of the patient's body.

• Declaration of Conformity EC
• Manual
• Manual (other languages)
• Setting up

ACCESSORIES / PRODUCTS TO BE USED WITH

Under knee pillow

Protective sleeve for the brace AM-RB