Home » SPINE BRACES » Thoracic-lumbar orthoses » SPINAL ORTHOSIS AM-WSP-04

SPINAL ORTHOSIS AM-WSP-04

The product is available while stocks last
SPINAL ORTHOSIS AM-WSP-04
4sport-en
TLSOTLSO
Anatomic staysAnatomic stays
BreathableBreathable
Class I medical deviceClass I medical device
DurableDurable
InnovativeInnovative
Brand: Code UNSPSC: Code UMDNS:
Code NFZ:

VAN

MALE DORSOLUMBAR BACK SUPPORT

Description

AM-WSP-04 High Dorso-Lumbar Back Support for Men with tensioners – GUMPERT was developed according to anatomical shape and to provide high level of stabilization at dorso-lumbar area of spine.

The Back part of support is made of Active3D™™ and AirRubber III™.

The Back Support is provided with anatomically shaped metal stays (sweat-resistant coating), which quantity depends on the size; 4 or 6 metal stays. The orthosis incorporates semi-rigid Back Plate which function is to provide reinforcement of lumbar stabilization.

The lateral side of back support is made of AeroSpace™.

An asymmetric closure allows the perfect fitting on the patient body. The panel of closure is made of velcro laminate with comfortable semi-rigid foam located inside, additionally provided with two elastic whalebones in the front. The system GRIP & OPEN makes the orthosis easy to assemble and disassemble.

Easy to apply due to the closure system with hand grip pockets, especially developed for patients with hands disability.

 

To improve the stabilization level of spine on dorso-lumbar area, the orthosis is equipped with system of three elastic tensioners.

The regulation of Back compression is obtained by system of three tensioners which together with semi-rigid Back Plate control the back traction and stabilization on lumbar region.

Properties

– PATIENT-FRIENDLY PRODUCT – The lumber support is made of cotton orthopaedic rubber containing mainly cotton which is neutral to the skin.
– HIGH EFFECTIVENSS OF STABILIZATION – thanks to the anatomically shaped nibs and set of tightening tapes it was possible to achieve very effective stabilization.
– SAFETY – the front securing tapes increase the safety of usage of the product and eliminate the possibility of the uncontrolled opening of the device.
– COMFORT OF USAGE – the product is light and comfortable to use.

Indications

– Pre- and Post-Surgical Stabilization
– Degenerative Spinal pathologies
– Disc Hernia
– Spondylolithesis
– Spondylolysis
– Acute Back Pain
– Spine Instability
– Rehabilitation and Prevention

Sizes

Size Waist circumference How to measure
S 65-75 cm
(25,6″-29,5″)
How to measure - waist circumference
M 75-85 cm
(29,5″-33,5″)
L 85-97 cm
(33,5″-38,2″)
XL 97-110 cm
(38,2″-43,3″)
XXL 110-125 cm
(43,3″-49,2″)
XXXL 125-145 cm
(49,2″-57,1″)

Total height of the product:
front: 25 cm (9,8″)
tył: 33 cm (13″)

Gallery

Click on the photo to enlarge

AM-WSP-04/AM-WSP-04/AM-WSP-04/AM-WSP-04/AM-WSP-04/AM-WSP-04/AM-WSP-04/AM-WSP-04/AM-WSP-04/AM-WSP-04/AM-WSP-04/AM-WSP-04/AM-WSP-04/AM-WSP-04/

Technology

MATERIALS

Active3D™

Active3D™ is thermoformed fabric made of special foamed, cell-closed designed material. It reduces the pressure on the body or any abrasions made by orthopaedic stays and aluminum splints. It is fully waterproof fabric and does not absorb sweat. It’s easy to clean. Due to its features, the fabric is an excellent product for making medical orthopaedic braces and orthoses. ACTIVE 3D™ has various external self-gripping layers. Our material has special, thermoformed properties and may be shaped according to the functional goals of the final braces.

AeroSpace™

AeroSpace™ is an innovative new generation raw material. It is a distance elastic 3D knitted fabric consisting of two layers of facings and an interlacing that creates the appropriate thickness of the raw material and has relieving properties. The knitwear is made of the highest quality polyester yarn - guaranteeing high mechanical strength and spandex ensuring its proper flexibility. This material is characterized by a very low weight, high flexibility and a very large openwork structure, allowing for very easy drainage of sweat from the body and bringing fresh air to the skin. Products made of this raw material are neutral to the secured joint, do not heat or cool it, but ensure its proper compression and fit and reduce muscle vibrations generated during physical exertion. Its thickness and 3D structure perfectly relieves the orthopedic splints, stays or other elements mounted on the product and guarantees velvety softness to the touch.

AirRubber III™

AirRubber III™ has unidirectional elasticity. It can be stretched, increasing the length, not width, what improves compression. Between the braids air flows freely and skin can breathe. In addition in high compression, these rubber braids provide a gentle massage for skin. Our orthopedic rubber is very friendly for skin.

STIFFENINGS

Lumbar supports

Low and high lumbar supports are made of polyethylene injection technology. The supports are embossed in the shape of the vertebrae of the spine, thanks to which it does not press on the spine, but relieves the back muscles. The product is equipped with the manufacturer's logo and a path for the seam. They stiffen the lumbar or thoracolumbar spine, relieve the muscle and stabilize the compression bands of the braces.

Lumbar supports

Orthopedic profiled stays

Orthopedic stays are made of special spring steel, covered with a plastic coating and have rounded and protected ends. They can come in various widths and thicknesses as well as different hardness. They can be pre-shaped or flat. They work in one direction and adapt to the shape of the body while stabilizing the laterally protected part of the body. They are perfectly protected against corrosion, so they are resistant to water, moisture and sweat. Products equipped with them can be washed without removing them from the orthosis. They adjust to the body. The orthopedic stays cannot bend and that is why, they cannot correct the body posture or the secured joint.

Orthopedic profiled stays

Plastic stays

They come in various widths and thicknesses, are made of various types of plastics, such as polyamide, ABS or acrylic, and these features determine their stiffness. Thanks to their design, they are resistant to water, moisture and sweat. Products equipped with them can be washed without having to remove them from the orthosis. Our plastic stays work only in one direction, perfectly stabilize the laterally protected part of the body, adjusting to it at the same time and have a memory function, thanks to which they always return to their original shape. This function causes the stays in the orthosis to stabilize the swollen limb immediately after the injury and after the swelling has come off. The plastic stays cannot bend and that is why, they cannot correct the body posture or the secured joint.

PADDINGS

3D supports

3D relief supports are independent technical solutions to relieve the rigid elements of a given orthosis. These elements are made of supporting foams or EVA foam. These foams are connected with various types of skin-friendly materials and materials with an adhesive function. These pads have the appropriate shape and color adapted to the type of orthosis. They relieve both metal elements of orthoses, such as splints, stays, underwires and orthopedic drop locks, as well as other elements that should not come into direct contact with the patient's skin. These pads have an anatomical shape and are made of comfortable foam with proper hardness and elasticity, guaranteeing the proper therapeutic effect.

Setting up

Downloads

Accessories

ACCESSORIES / PRODUCTS TO BE USED WITH

Code AM-WSP-04
Trade Name SPINAL ORTHOSIS
Model Back brace AM-WSP-04

ON OUR WEBSITE WE PRESENT MEDICAL DEVICES.
USE THEM ACCORDING TO THE INSTRUCTIONS FOR USE OR LABEL.

CEMDClass I medical device in accordance with Regulation (EU) 2017/745 of the European Parliament and of the Council of 5 April 2017. on medical devices.

MANUFACTURER / ADVERTISING ENTITY: REH4MAT Sp. z o.o.