LOWER BACK BRACE AM-SO-06

AM-SO-06 lumbar back support with double closure panels was developed in order to improve the stabilization level on the spine maintaining comfort and its functionality for the patient.

The orthosis was developed according to anatomical shape, allowing the perfect fitting and adequate stabilization level of lumbar area.

The Back part of orthosis is made of Active3D™. Side parts are made of AirRubber™.

The orthosis is provided with anatomically shaped metal stays (sweat-resistant coating), which quantity depends on the size; 4 or 6 metal stays in the Back.

The Front Panel closure is composed of four independent closures, made in semi-rigid medical laminate covered by velcro adherence textile. The Double closure construction makes the orthosis easy-fitting to different body shapes (especially recommended for women).

In order to allow the easy fitting and correct adjustment on the patient body, the Back Support is provided with two edges in the Front, to park the flaps of velcro tensioners.

In order to improve the functionality of the product, the orthosis is equipped with two sets of three- layer elastic tensioners, which offer high stabilization and support on lumbar and sacro-lumbar area.

Properties

– SKIN FRIENDLY PRODUCT – lumber support has been made of special orthopaedic rubber, which is neutral to patient’s skin
– EFFECTIVENSS OF STABILIZATION – the stabilization is exceptionally good thanks to the orthopaedic nibs, tightening rubber belts crossed at the back and anatomically shaped loin pillow.
– SAFETY – the front tightening rubber belts provide additional protection and the chances of the device to undo accidentally are eliminated.
– COMFORT OF USAGE – the limber support is very light and therefore comfortable to wear.

Indications

– Pre- and Post-Surgical Stabilization
– Degenerative Spinal pathologies on Lumbar area
– Disc Hernia
– Lumbar Muscles and Ligamentous Strains and Sprains
– Postural Support
– Chronic Low Back Pain
– Rehabilitation and Prevention

Size	Waist circumference	How to measure
S	65-75 cm (25,6″-29,5″)
M	75-85 cm (29,5″-33,5″)
L	85-97 cm (33,5″-38,2″)
XL	97-110 cm (38,2″-43,3″)
XXL	110-125 cm (43,3″-49,2″)
XXXL	125-145 cm (49,2″-57,1″)

S – last items
Total height of the product:
front: 27 cm (10,6″)
tył: 30 cm (11,8″)

Click on the photo to enlarge

MATERIALS

Active3D™

Active3D™ is thermoformed fabric made of special foamed, cell-closed designed material. It reduces the pressure on the body or any abrasions made by orthopaedic stays and aluminum splints. It is fully waterproof fabric and does not absorb sweat. It’s easy to clean. Due to its features, the fabric is an excellent product for making medical orthopaedic braces and orthoses. ACTIVE 3D™ has various external self-gripping layers. Our material has special, thermoformed properties and may be shaped according to the functional goals of the final braces.

AirRubber™

AirRubber™ has unidirectional elasticity and it’s breathable. This lamination is perforated. Between the braids air flows freely and skin can breathe. In addition in high compression, these rubber braids provide a gentle massage for skin. Our orthopedic rubber is very friendly for skin.

STIFFENINGS

Lumbar supports

Low and high lumbar supports are made of polyethylene injection technology. The supports are embossed in the shape of the vertebrae of the spine, thanks to which it does not press on the spine, but relieves the back muscles. The product is equipped with the manufacturer's logo and a path for the seam. They stiffen the lumbar or thoracolumbar spine, relieve the muscle and stabilize the compression bands of the braces.

Orthopedic profiled stays

Orthopedic stays are made of special spring steel, covered with a plastic coating and have rounded and protected ends. They can come in various widths and thicknesses as well as different hardness. They can be pre-shaped or flat. They work in one direction and adapt to the shape of the body while stabilizing the laterally protected part of the body. They are perfectly protected against corrosion, so they are resistant to water, moisture and sweat. Products equipped with them can be washed without removing them from the orthosis. They adjust to the body. The orthopedic stays cannot bend and that is why, they cannot correct the body posture or the secured joint.

Orthopedic stays from ABS

Orthopedic stays available in various width, thickness and shapes are cut from ABS boards. Their role is not to stiffen the orthosis in order to support a joint or other part of the body, but to prevent wrinkling and uncontrolled movement of the fabrics of the orthosis./p>

PADDINGS

3D supports

3D relief supports are independent technical solutions to relieve the rigid elements of a given orthosis. These elements are made of supporting foams or EVA foam. These foams are connected with various types of skin-friendly materials and materials with an adhesive function. These pads have the appropriate shape and color adapted to the type of orthosis. They relieve both metal elements of orthoses, such as splints, stays, underwires and orthopedic drop locks, as well as other elements that should not come into direct contact with the patient's skin. These pads have an anatomical shape and are made of comfortable foam with proper hardness and elasticity, guaranteeing the proper therapeutic effect.

• Declaration of Conformity EC
• Manual
• Setting up

ACCESSORIES / PRODUCTS TO BE USED WITH

Silicone pressure pad AM-PS

Thermoforming pad AM-PT